YPWO4025#4A三螺杆泵、机床冷却泵
PO6 SEIM系列的三螺旋泵的设计工作与机床冷却剂为高压泵的应用程序。It’s self-priming capability and low noise level allows continuous duty at 100 bar （1450 PSI） with typically water-based emulsions.这是自吸能力和低噪音水平允许连续运行在100巴（1450 PSI）与一般水性乳剂。
The PO's series inlet port is available in either axial or radial configurations and the PO Series operates at 5 to 74 GPM at pressures up to 1450 PSI at a temperature range of 32° to 140° F.PO的系列进气口有要么轴向或径向配置和PO系列操作在5到74流量在1450 PSI的压力在一个温度范围的32°至140°F。
SEIM screws pumps are volumetric self-priming pumps suited to handle various oils and also other fluids with minimum lubricating properties. SEIM螺丝泵体积自吸泵适合处理各种油类和其他液体与zui低的润滑性能。The pumps design makes them intrinsically reliable and efficient in their applications.泵的设计使其在本质上可靠和有效的在他们的应用程序。
功能特性的一个SEIM螺旋泵:
Very low noise levels非常低的噪音水平
Wide range viscosity compatibility广泛粘度兼容性
High rotation rates = minimizing the size and cost of the pump高旋转zui小化大小和成本的泵
No vibrations没有振动
Minimum sensitivity to particle pollutionzui小灵敏度粒子污染
High self-priming capacity高自吸能力
Special design for systems with entrained air in the lubricant特殊设计的系统加气的润滑剂
During operation, the PO entraps air bubbles inside is body to suppress system noise在操作期间,阿宝entraps气泡内的身体来抑制系统噪声
SEIM PO Screw PumpsSEIM阿宝螺杆泵
SEIM - PO Series Pump TypeSEIM - PO系列泵型
3 Screw Pump3螺杆泵
Horizontal Pump Mounting卧式泵安装
SEIM - PO Series MaterialsSEIM - PO系列材料
316 Stainless Steel316不锈钢
Cast Iron铸铁
SEIM - PO Series IndustriesSEIM - PO系列产业
Clear Liquids Pumping Applications清澈液体泵应用
Oil Pumping Applications泵油应用
High Viscosity Fluid Pumping高粘度流体泵送
Plant Engineering Pumping植物工程泵送
SEIM - PO Series ApplicationsSEIM - PO系列应用程序
Recirculation Systems Pumping再循环系统抽水
Lubrication Systems Pumping润滑系统抽水
High Pressure Pumping高压泵
1、三螺杆泵的吸入、排出管径不得小于泵的进、出口口径，入口管路力求简短，减少不必要的损失如弯头等，泵的安装高度应保证泵工作时不超过允许的吸上真空高度。
1, three screw pump suction, exhaust pipe diameter shall be not less than the pump inlet,outlet pipe diameter, entrance to brief, reduce unnecessary losses such as the elbow, the pump mounting height should ensure that the pump works without exceeding the permissiblesuction height.
2、管路应有管架，泵不允许承受管路的负荷。
2, the pipeline should be the pipe rack, pump is not allowed under the load of pipeline.
3、安装前对吸入、排出管路要清理干净，特别是吸入管路的焊渣必须*清除，以免进入泵后咬死。
3, before installation of suction, exhaust pipe to clean up, especially the welding slag suction pipeline must be compley removed, lest enter the pump after seizure.
4、吸入管路应装设过滤器，其滤网为40-80目，有效过滤面积应大于泵吸入口径20-30倍。
4, the suction line should be installed with a filter, the filter of 40-80 mesh, the effective filtration area should be larger than the pump suction diameter 20-30 times. Connecting the
5、泵的进、出口处连接真空和压力表，以便观察泵的工作状态。
5, the pump inlet, outlet vacuum and pressure gauge, in order to observe the pump working condition.
6、如有两台以上的泵并联在同一管路上，在泵出口处必须安装逆止阀，保证泵的正常工作。
6, if the pumps and two or more in the same pipeline, the pump outlet check valve must be installed, and ensure the normal work of the pump
7、安装泵的位置应宽敞、方便检修。
7, pump installation location should bespacious, convenient maintenance.
8、将机组放在埋有地脚螺栓的基础上，找正后拧紧地脚螺栓。
8, will be buried on the unit have the foundation anchor bolts, anchor bolts tightened after alignment.
9、在接好管路及确定电机转向后接联轴器，联轴器外圆同轴度允差0.1mm,两联轴器端面间隙允差2mm。
9, in the connected pipeline and determine the motor turn coupling, coaxial degree allowscoupling outer circle 0.1mm, coupling the two end clearance tolerance 2mm.
10、机组运转3-4小时后作zui后的检查，如无不良现象，则认为安装合格。
10, unit operation 3-4 hours after the final check, if no bad phenomenon, is consideredqualified installation.
11、与三螺杆泵联接的进出口管道，法兰一定要清洁，严禁杂质、焊渣残留管内
11, and the three screw pump inlet and outlet pipe flange connection, must be clean, noimpurities, welding slag residue tube
公 司 名称： | 黄山天曼泵业有限公司 |
姓名： | 程晓 （销售 ） （） |
办 公 地址： | 中国 黄山市徽州区城北工业园 |
邮 编： | 245400 |
电 话： | 86- |
传 真： | 86- |
移 动 ： | |
邮 箱： | Hstmby01 |
： |
|
阿 里 旺旺: | 旺旺：hstmby01 |
公司主页： | http;//www.hstmby.comhttp://www.luogb.com http://www.cntmby.comhttp://www.tm-p.cc |
Company name: Mount Huangshan teamon pump industry limited company
Contact person: Mr. Cheng Xiao （Sales Manager） （）
Office address: China Huangshan City Huizhou area north of the City Industrial Park
Postal Code: 245400
86-
86-
phone:
: Hstmby01
: :
A: I want to: hstmby01
Company homepage: http; //www.hstmby.comhttp://www.luogb.com
http://www.cntmby.comhttp://www.tm-p.cc
