粉碎设备 混合设备 分离设备 浓缩结晶设备 传质设备 干燥设备 反应设备 换热设备 制冷设备 空分设备 储存设备 锅炉|加热设备 包装机械 输送设备 化工实验室设备
波尔高压电源有限公司
产品详细介绍 Genvolt8000系列是一款坚固耐用的模块化系列直流高电压供应范围,电源输入电压从85VAC-265VAC50/60Hz
The Genvolt 8000 series is a rugged modularised range of AC-input DC High Voltage supplies, designed to operate from a universal mains input from 85VAC to 256VAC 50/60Hz. Power Output options from 1kv to 70kV.
They feature an active boost-style Power Factor Correction front end – i.e. an active rectifier. This offers a very low harmonic distortion at mains frequencies with a power factor of up to 0.99.
The modules have a FIXED polarity output which should be specified at the time ordering using the “Model Finder” table.
They operate in both Voltage Control and Current Control modes with fast active crossover between the modes.
Protection against output short circuits or arcs, over temperature and output overvoltage allow for operation in demanding environments.
AC Input voltage range | 85VAC to 256VAC, 47 – 63 Hz |
---|---|
Power Factor | FL 0.99 NL 0.98 |
Output Polarity | +ve or –ve (Please specify when ordering) |
Voltage Load Regulation | 0.01% of full voltage for a no load to a full load change |
Voltage Line Regulation | +/- 0.005% of full voltage over the specified input voltage range |
Current Load Regulation | 0.01% from 0V to full voltage |
Current Line Regulation | +/- 0.01% of full current over the specified input voltage range per 8 hours after |
Voltage Ripple: | 0.1% p-p of output voltage |
Current Stability | 0.02% per 8hrs after ½hr warm up |
Temperature Coefficient | 100 ppm per oC |
Temperature | Operating 0oC to 45oC Storage -20oC to +85oC |
Interlock | Open Interlock will shut down unit |
Circuit Protection | Overvoltage, Overcurrent, Arcing and Over temperature |
Relative Humidity | Non condensing |
The control signal is NOT a safety interlock and must NOT be used for a protection system from high voltage generation for safety purposes.
Control | Logic level for high voltage enable/disable. |
---|---|
Overvoltage Protection | Overvoltage conditions can be caused by excessive input program signal. If an overvoltage condition is detected, the power supply is latched off until input power is reset. |
PS Fault Condition | A PS fault indicator and a PS fault output on J1, indicate an OVP or a regulation error. |
PF and Universal Input | The input voltage of the 8000 can operate within the range from 85VAC to 265VAC. The power factor is actively corrected across the entire range and is better than 0.99 at full load. |
Internal EMI Filter | An internal EMI filter and fuse provide protection against line voltage surges and power supply faults |
Remote Programming | Allows remote adjustment of the output voltage and current, via an external voltage source. |
---|---|
Remote Monitor | Allows remote monitoring of the output voltage and current. |
High Voltage Enable/Disable | Allows remote ON/OFF control of the high voltage. |
+10VDC Reference | A +10VDC is provided for remote programming via a potentiometer or voltage divider. |
Weight | Model specific, approximately 3Kgs |
---|---|
Dimensions | 95.25mm (H) x 127mm (W) x 279.4mm (D) |
Power Input Connector | IEC320 with mating connector x 2 Metres |
HV Output Connector | Proprietary HV Connector |
Control Interface Connector | 15 pin ‘D’ connector (Male) |
Maximum Voltage | Maximum Current | Polarity | Model Number |
1kV | 120mA | P or N | 80120P (+ve) or 80120N (-ve) |
5kV | 24mA | P or N | 8024P (+ve) or 8024N (-ve) |
10kV | 12mA | P or N | 8012P (+ve) or 8012N (-ve) |
20kV | 6mA | P or N | 806P (+ve) or 806N (-ve) |
30kV | 4mA | P or N | 804P (+ve) or 804N (-ve) |
40kV | 3mA | P or N | 803P (+ve) or 803N (-ve) |
50kV | 2.4mA | P or N | 8050P (+ve) or 8050N (-ve) |
60kV | 2mA | P or N | 8060P (+ve or 8060N (-ve) |
70kV | 1.7ma | P or N | 8070P (+ve) or 8070N (-ve) |
您感兴趣的产品PRODUCTS YOU ARE INTERESTED IN
化工机械设备网 设计制作,未经允许翻录必究 .
请输入账号
请输入密码
请输验证码
请输入你感兴趣的产品
请简单描述您的需求
请选择省份